KTM 690 DUKE, r.v. 2014
REAR BRAKE RESERVOIR COVER
19,28 EUR
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight
OILFILTER SERVICE KIT 690
60,66 EUR
The oil filter kit contains all the filters, sieves, O-rings and seals you need for an oil change.
SERVICE PIT MAT
134,3 EUR
This mat is already mandatory for many races Complies with FIM regulations The special material mix absorbs overflowing fuel The mat also facilit...
TOOL BAG BLACK SC '99
15,39 EUR
The optimum solution for always having the most important tools to hand when on the road.
HAND BRAKE CYL. COVER
27,00 EUR
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight
REAR BRAKE RESERVOIR COVER
19,28 EURCNC milled from high-strength aluminum Elegant anodised surface Visual highlight
OILFILTER SERVICE KIT 690
60,66 EURThe oil filter kit contains all the filters, sieves, O-rings and seals you need for an oil change.
SERVICE PIT MAT
134,3 EURThis mat is already mandatory for many races Complies with FIM regulations The special material mix absorbs overflowing fuel The mat also facilit...
TOOL BAG BLACK SC '99
15,39 EURThe optimum solution for always having the most important tools to hand when on the road.
HAND BRAKE CYL. COVER
27,00 EURCNC milled from high-strength aluminum Elegant anodised surface Visual highlight
LOCATING SCREW
Tool for securing components (crankshaft in TDC position)
SPOKE TORK KEY
Torque wrench with various bits in the kit for tightening fittings to tightening torque (spokes)
ATTACHMENT F. SPOKE TORK
Tool for tightening steering head bearing
BUSHING EXTRACTOR
Tool for removing bearings from a housing
INTERN.BEAR.PULLER 18-23 MM
Tool for removing bearings from a housing
MAGNETO EXTRACTOR
Tool for pulling off components (rotor)
MOUNTING TOOL F.BEARING NJ 207
Tool for pulling off components (inner bearing race of crankshaft)
EXTRACTOR PRIM. CPL.
Tool for pulling off components (primary gear wheel)
EXTRACTOR FOR TIMING GEAR
Tool for pulling off components (timing chain sprocket)
HOUSING SEPARATING TOOL
Tool for disengaging components (sections of the engine case)
MOUNT.SLEEVE F. SH.S.RING WAPU
Tool for protecting components (installation of crankshaft and balancer shaft)
MOUNT.SLEEVE F. SH.S.RING MS
Tool for protecting components (installation of crankshaft, balancer shaft and engine case)
MOUNT.SLEEVE F. SH.S.RING KS
Tool for protecting components (installation of crankshaft and balancer shaft)
PROTECTOR CAP F.CRANKSHAFT 07
Tool for protecting components (removal of primary gear wheel)
VEHICLE STAND
Tool for lifting the motorcycle at the center
ATTACHMENT SHUNTING JACK CPL.
Attachment for floor jack, for lifting engine
PLIERS F. VAR.ONE-EAR CLAMP 03
Tool for mounting hose clamps
SP. BROCKET SW.ARM BEARING ADJ
Tool for adjusting, removing and installing components with groove nuts
PRESS. TOOL F. CRANKS. CPL.
Tool for pressing the crankshaft together
PRESS OUT PLATE TOP PART
Tool for separating the crankshaft
PRESS OUT PLATE BOTTOM PART
Tool for separating the crankshaft
PISTON R. COMPRESSOR DM=102
Tool for installing the piston in the cylinder
PLUG IN FUSE PISTON PIN
Tool for installing the piston ring lock in the piston
ASSEMBLY TOOL CIRCLIP
Tool for mounting lock rings on the drive and countershaft
MOUNTING SCREWS
4 screws for tensioning the slipper clutch
ON TENSIONER PL. CYLINDER HEAD
Plate for mounting the cylinder head
VALVE SPRING LEVER
Tool for installing and removing valves and valve springs
LIMIT PLUG GAUGE F.VALVE GUIDE
Tool for checking valve guides