KTM, r.v. 2024
REAR BRAKE RESERVOIR COVER
485 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight
CHARGER EU
24 075 Kč
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
STEERING DAMPER KTM 1290 SD R KPL.
9 695 Kč
Developed for use on the race track Prevents unpleasant handlebar hits High-end WP suspension steering damper Tested in the IDM and Moto3™ Dampin...
CNC OIL FILL PLUG LC8
922 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight Includes drilling for safety wire
REAR BRAKE RESERVOIR COVER
485 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight
CHARGER EU
24 075 KčSpecially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
STEERING DAMPER KTM 1290 SD R KPL.
9 695 KčDeveloped for use on the race track Prevents unpleasant handlebar hits High-end WP suspension steering damper Tested in the IDM and Moto3™ Dampin...
CNC OIL FILL PLUG LC8
922 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight Includes drilling for safety wire
NITROGEN FILL DEVICE 2005
Tool for filling the damper with nitrogen
DE-MOUNT.TOOL KGW SWIVEL BEAR.
Tool for pressing in components (heim joint)
CLAMPING BLOCK F. PIPE 48/60
Tool for clamping components (fork legs, outer fork tube)
CHARGER USA
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and...
CHARGER GB
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and...
BRAKE BLEEDER COVER
Adapter for hand or foot brake cylinder, for filling or bleeding the brake system
BLEEDER COVER
Adapter for hand or foot brake cylinder, for filling or bleeding the brake system
UNIVERSAL MOUNTING RACK
Tool (including chassis, crank rotation mechanism, oil pan, and engine bracket) for mounting the rem...
MOUNTING EQUIPMENT 617
Separate tool for mounting large engines on the engine work stand
GRIP FOR RING WRENCH
Extension of the holding wrench tool set, for turning components (rear hub)
HOOK WRENCH ECCENTRIC REAR WH.
Tool set, for turning components (rear hub)
DEGREE DISK 360DEG - 1/2 INCH
Tool for tightening bolts with rotation angle (cylinder head nuts, conrod bearing bolts)
PLASTIGAUGE - MEASURING STRIP
Tool for measuring bearing play
BUSHING EXTRACTOR
Tool for removing bearings from a housing
INTERN.BEAR.PULLER 18-23 MM
Tool for removing bearings from a housing
EXTRACTOR PRIM. CPL.
Tool for pulling off components (primary gear wheel)
INTERN.BEAR.PULLER 28 MM
Tool for removing bearings from a housing
PULLER CPL. F. IGNITION COVER
Tool for pulling off components (alternator cover)
PULLER F. COUNTERSHAFT DRIVE
Arms for puller, for pulling off components (primary gear, drive gear wheel of the balancer shaft)
PULLER
Tool for pulling off components (primary gear, drive gear wheel of the balancer shaft)
MOUNTING SLEEVE WD-RING
Tool for protecting components (installation of clutch cover)
VEHICLE STAND
Tool for lifting the motorcycle at the center
PISTON RING COMPRESSOR CPL. 03
Tool for tensioning piston rings when installing the piston in the cylinder
PLUG IN FUSE PISTON PIN
Tool for installing the piston ring lock in the piston
VALVE SPRING LEVER
Tool for installing and removing valves and valve springs
