KTM 890 DUKE GP, r.v. 2023
HANDLEBAR ENDS RIGHT+LEFT 05
387 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight Prevents the hand grips from chafing in the event of a fall
FACTORY TRANSPORT COVER
242 Kč
Provides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 Kč
Use this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
CNC OIL FILL PLUG LC8
922 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight Includes drilling for safety wire
ALARM SYSTEM
8 481 Kč
Plug & Play mounting Wiring harness ready for fitting Fail-safe, dual-circuit immobiliser Integrated microchip motion sensor Two watertight, anti...
HANDLEBAR ENDS RIGHT+LEFT 05
387 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight Prevents the hand grips from chafing in the event of a fall
FACTORY TRANSPORT COVER
242 KčProvides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 KčUse this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
CNC OIL FILL PLUG LC8
922 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight Includes drilling for safety wire
ALARM SYSTEM
8 481 KčPlug & Play mounting Wiring harness ready for fitting Fail-safe, dual-circuit immobiliser Integrated microchip motion sensor Two watertight, anti...
CLAMPING BLOCK 4054
Tool for clamping components (outer tube, fork leg)
DE-MOUNT.TOOL KGW SWIVEL BEAR.
Tool for pressing in components (heim joint)
DIAGNOSTIC TABLET AC ADAPTER
Battery charger and power supply unit for Getac F110 diagnostics tablet
VCI MOUNT
Attachment for the VCI including an attachment for the fuel tank
PROTECTIVE FOIL
Protective film for the touchscreen of the Getac F110 diagnostics tablet
DIAGNOSTIC CABLE EXTENSION
Extension cables between VCI and diagnostic connector on the vehicle
12 V SUPPLY CABLE
External power supply for the VCI for vehicles without 12-V battery and for flashing of specific con...
STYLUS
Stylus for input via the touch screen of the Getac F110 diagnostics tablet
UNIVERSAL MOUNTING RACK
Tool (including chassis, crank rotation mechanism, oil pan, and engine bracket) for mounting the rem...
ASSEMBLY JIG 63
Separate tool for mounting large engines on the engine work stand
SWING ARM FIXING TOOL
Tool for securing the link fork when the engine is removed
DEGREE DISK 360DEG - 1/2 INCH
Tool for tightening bolts with rotation angle (cylinder head nuts, conrod bearing bolts)
PLASTIGAUGE - MEASURING STRIP
Tool for measuring bearing play
ORIENTATION JIG UPPER BALANCER SHAFT
Tool for aligning the upper balancer shaft
BUSHING EXTRACTOR
Tool for removing bearings from a housing
INTERN.BEAR.PULLER 12-16 MM
Tool for removing bearings from a housing
EXTRACTOR PRIM. CPL.
Tool for pulling off components (primary gear wheel)
PULLER CPL. F. IGNITION COVER
Tool for pulling off components (alternator cover)
VEHICLE STAND
Tool for lifting the motorcycle at the center
ATTACHMENT SHUTING JACK CPL.
Attachment for floor jack, for lifting and tilting the engine
PLIERS F. VAR.ONE-EAR CLAMP 03
Tool for mounting hose clamps
SEPARATOR PLATE CRANKSHAFT
Tool for separating the crankshaft
PISTON RING COMPRESSOR CPL. 03
Tool for tensioning piston rings when installing the piston in the cylinder
