KTM 1290 SUPER DUKE R EVO, r.v. 2023
REAR BRAKE RESERVOIR COVER
485 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight
STEERING DAMPER KTM 1290 SD R KPL.
9 695 Kč
Developed for use on the race track Prevents unpleasant handlebar hits High-end WP suspension steering damper Tested in the IDM and Moto3™ Dampin...
FACTORY TRANSPORT COVER
242 Kč
Provides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 Kč
Use this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
CNC OIL FILL PLUG LC8
922 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight Includes drilling for safety wire
REAR BRAKE RESERVOIR COVER
485 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight
STEERING DAMPER KTM 1290 SD R KPL.
9 695 KčDeveloped for use on the race track Prevents unpleasant handlebar hits High-end WP suspension steering damper Tested in the IDM and Moto3™ Dampin...
FACTORY TRANSPORT COVER
242 KčProvides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 KčUse this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
CNC OIL FILL PLUG LC8
922 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight Includes drilling for safety wire
GRIP FOR RING WRENCH
Extension of the holding wrench tool set, for turning components (rear hub)
HOOK WRENCH ECCENTRIC REAR WH.
Tool set, for turning components (rear hub)
DEGREE DISK 360DEG - 1/2 INCH
Tool for tightening bolts with rotation angle (cylinder head nuts, conrod bearing bolts)
PLASTIGAUGE - MEASURING STRIP
Tool for measuring bearing play
EXTENSION TORQUE WRENCH
Bit for torque wrench, for tightening fittings to tightening torques (camshaft bearing support)
BUSHING EXTRACTOR
Tool for removing bearings from a housing
INTERN.BEAR.PULLER 18-23 MM
Tool for removing bearings from a housing
EXTRACTOR PRIM. CPL.
Tool for pulling off components (primary gear wheel)
INTERN.BEAR.PULLER 28 MM
Tool for removing bearings from a housing
PULLER CPL. F. IGNITION COVER
Tool for pulling off components (alternator cover)
PULLER F. COUNTERSHAFT DRIVE
Arms for puller, for pulling off components (primary gear, drive gear wheel of the balancer shaft)
PULLER
Tool for pulling off components (primary gear, drive gear wheel of the balancer shaft)
VEHICLE STAND
Tool for lifting the motorcycle at the center
PISTON RING COMPRESSOR CPL. 03
Tool for tensioning piston rings when installing the piston in the cylinder
PLUG IN FUSE PISTON PIN
Tool for installing the piston ring lock in the piston
VALVE SPRING LEVER
Tool for installing and removing valves and valve springs
VALVE SPRING TENSION APPLICAT.
Tool for installing and removing valves and valve springs
PRESS TOOL DM28
Tool for pressing components in (crankshaft support bearing)
PRESS. PIN-FLYWHEEL EXTRACTOR
Tool for pressing out components (removing rotor)
ARBOR PRESS SS-RING DRIVE
Tool for pressing components in (radial shaft seal ring push rod)
PRES.SOCKET COUNTERSHAFT DRIVE
Tool for pressing in components (drive gear wheel of the balancer shaft)
COMBINATION PRESSURE PAD
Tool for pressing out components (drive gear wheel of the balancer shaft)
PRESSING TOOL D53 MAIN BEARING
Tool for pressing bearing shells in and out (main bearing)
BEARING RING F. PRESSING TOOL
Tool for pressing components in and out (main bearing)
PRESSING DORN SWINGARM BEARING
Tool for pressing components in and out (fork bearing)
COUNTER TORQUE WRENCH SWINGARM
Tool for pressing components out (fork bearing)
SPECIAL SOCKET F.CYL.-HEAD NUT
Tool for removing and mounting screws (conrod bearing)
