KTM, r.v. 2017
REAR BRAKE RESERVOIR COVER
485 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight
CHARGER EU
24 075 Kč
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
HANDLEBAR ENDS RIGHT+LEFT 05
387 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight Prevents the hand grips from chafing in the event of a fall
FACTORY TRANSPORT COVER
242 Kč
Provides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 Kč
Use this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
REAR BRAKE RESERVOIR COVER
485 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight
CHARGER EU
24 075 KčSpecially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
HANDLEBAR ENDS RIGHT+LEFT 05
387 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight Prevents the hand grips from chafing in the event of a fall
FACTORY TRANSPORT COVER
242 KčProvides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 KčUse this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
LOCATING SCREW
Tool for securing components (crankshaft in TDC position)
SPOKE TORK KEY
Torque wrench with various bits in the kit for tightening fittings to tightening torque (spokes)
ATTACHMENT F. SPOKE TORK
Tool for tightening steering head bearing
BUSHING EXTRACTOR
Tool for removing bearings from a housing
INTERN.BEAR.PULLER 18-23 MM
Tool for removing bearings from a housing
MOUNTING TOOL F.BEARING NJ 207
Tool for pulling off components (inner bearing race of crankshaft)
EXTRACTOR PRIM. CPL.
Tool for pulling off components (primary gear wheel)
EXTRACTOR FOR TIMING GEAR
Tool for pulling off components (timing chain sprocket)
HOUSING SEPARATING TOOL
Tool for disengaging components (sections of the engine case)
MOUNT.SLEEVE F. SH.S.RING WAPU
Tool for protecting components (installation of crankshaft and balancer shaft)
MOUNT.SLEEVE F. SH.S.RING MS
Tool for protecting components (installation of crankshaft, balancer shaft and engine case)
MOUNT.SLEEVE F. SH.S.RING KS
Tool for protecting components (installation of crankshaft and balancer shaft)
PROTECTOR CAP F.CRANKSHAFT 07
Tool for protecting components (removal of primary gear wheel)
VEHICLE STAND
Tool for lifting the motorcycle at the center
BRACKET FOR ASSEMBLING RACK
Attachments for work stand, for lifting the motorcycle at the center
ATTACHMENT SHUNTING JACK CPL.
Attachment for floor jack, for lifting engine
PLIERS F. VAR.ONE-EAR CLAMP 03
Tool for mounting hose clamps
PLIERS F.VALVE-STEAM SEALING
Tool for removing valve stem seals
SP. BROCKET SW.ARM BEARING ADJ
Tool for adjusting, removing and installing components with groove nuts
PRESS. TOOL F. CRANKS. CPL.
Tool for pressing the crankshaft together
PRESS OUT PLATE TOP PART
Tool for separating the crankshaft
PRESS OUT PLATE BOTTOM PART
Tool for separating the crankshaft
PRESS. TOOL F. CRANKSHAFT
Cover for pressing tool for pressing the crankshaft together
PISTON RING COMPRESSOR CPL. 03
Tool for tensioning piston rings when installing the piston in the cylinder
PISTON R. COMPRESSOR DM=102
Tool for installing the piston in the cylinder
PLUG IN FUSE PISTON PIN
Tool for installing the piston ring lock in the piston
ASSEMBLY TOOL CIRCLIP
Tool for mounting lock rings on the drive and countershaft
