KTM, r.v. 2017
CHARGER EU
24 075 Kč
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
FACTORY TRANSPORT COVER
242 Kč
Provides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 Kč
Use this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
REAR BAG
3 378 Kč
Fastening with Quicklock system Extremely robust fasteners, with large zip pullers Made of the highest quality materials Custom design Rain cover...
ALARM SYSTEM
8 481 Kč
Plug & Play mounting Wiring harness ready for fitting Fail-safe, dual-circuit immobiliser Integrated microchip motion sensor Two watertight, anti...
CHARGER EU
24 075 KčSpecially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
FACTORY TRANSPORT COVER
242 KčProvides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 KčUse this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
REAR BAG
3 378 KčFastening with Quicklock system Extremely robust fasteners, with large zip pullers Made of the highest quality materials Custom design Rain cover...
ALARM SYSTEM
8 481 KčPlug & Play mounting Wiring harness ready for fitting Fail-safe, dual-circuit immobiliser Integrated microchip motion sensor Two watertight, anti...
ASSEMBLING TOOL CRANKSH.BEAR.
Tool for pulling off components (main bearing)
HOUSING SEPARATING TOOL
Tool for disengaging components (sections of the engine case, for pressing out the crankshaft)
PROTECTION SLEEVE WDR AGW
Tool for protecting components (water pump installation)
PROTECT. SLEEVE F. CRANKSHAFT
Tool for protecting components (removal of crankshaft, main bearing)
VEHICLE STAND
Tool for lifting the motorcycle at the center
ATTACHMENT SHUNTING JACK CPL.
Attachment for floor jack, for lifting engine
SPECIAL SOCKET CLUTCH
Tool for adjusting, removing and installing components with groove nuts
SP. BROCKET SW.ARM BEARING ADJ
Tool for adjusting, removing and installing components with groove nuts
SOCKET SW=17
Tool for adjusting, removing and installing components with groove nuts
SOCKET F.STEERINGHEAD BEARING
Tool for adjusting, removing and installing components with groove nuts
SOCKET F.STEERINGHEAD BEARING
Tool for adjusting, removing and installing components with groove nuts
SEPARATOR PLATE CRANKSHAFT
Tool for pressing out balancer shaft drive gear wheel
PISTON RING COMPRESSOR CPL. 03
Tool for tensioning piston rings when installing the piston in the cylinder
PLUG IN FUSE PISTON PIN
Tool for installing the piston ring lock in the piston
VALVE SPRING LEVER
Tool for installing and removing valves and valve springs
LIMIT PLUG GAUGE F.VALVE GUIDE
Tool for checking valve guides
INSERT FOR VALVE SPRING LEVER
Tool for installing and removing valves and valve springs
ASSEMBLY TOOL WATERPUMP GASKET
Tool for pressing in components (radial shaft seal ring)
ASSEMBLY TOOL AGW-BEARING
Tool for pressing components out (balancer shaft bearing)
MOUNTING TOOL WATER PUMP SEAL
Tool for pressing in components (radial shaft seal ring)
PIN KEY FOR FRONTFORK
Tool for loosening and tightening components (sliding bushing support)
PRE LOAD KEY 4681 STEEL
Tool for tensioning and releasing the springs (two units)
DRIVETRAIN KIT 200 DUKE14T/42T
This drive kit consists of a 14 tooth front and a 42 tooth rear sprocket wheel, a DID chain and mast...
DRIVETRAIN KIT DUKE 2015
This drive kit consists of a 14 tooth front and a 42 tooth rear sprocket wheel, a DID chain and mast...
GRIP SET
The grip set includes a twist grip and a fixed grip.
PISTON KIT 200 DUKE 12-13
This piston kit includes the piston and all the seals required to change the piston.
CLUTCH KIT 200 DUKE 12-15
The clutch kit contains everything you need to repair your clutch.
