KTM 690 SMC R, r.v. 2014
REAR BRAKE RESERVOIR COVER
485 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight
CHARGER EU
24 075 Kč
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
HANDLEBAR ENDS RIGHT+LEFT 05
387 Kč
CNC milled from high-strength aluminum Elegant anodised surface Visual highlight Prevents the hand grips from chafing in the event of a fall
FACTORY TRANSPORT COVER
242 Kč
Provides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 Kč
Use this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
REAR BRAKE RESERVOIR COVER
485 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight
CHARGER EU
24 075 KčSpecially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and lithium-ion), backup operation with diagnosi...
HANDLEBAR ENDS RIGHT+LEFT 05
387 KčCNC milled from high-strength aluminum Elegant anodised surface Visual highlight Prevents the hand grips from chafing in the event of a fall
FACTORY TRANSPORT COVER
242 KčProvides optimum protection For rear sprockets up to 50T and 220 mm - 260 mm brake discs.
MUD REMOVAL TOOL
242 KčUse this to remove the dirt from your last mud battle with ease! A motorcycle grip rubber (not included) can be fitted to the grip.
STYLUS
Stylus for input via the touch screen of the Getac F110 diagnostics tablet
BREAKOUT-BOX
Box with connector board (without adapter and templates) for performing various electrical measureme...
CHARGER USA
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and...
ADAPTER LC4 KHRS
Adapter cable and template for performing various electrical measurements on the wiring harness
CHARGER GB
Specially designed battery charger for the correct charging of various 12-V batteries (acid, AGM and...
CABLEPLUG OUTPINSET
Pinout kit including case and crimping pliers for repairing wiring harnesses or replacing the most c...
BRAKE BLEEDER COVER
Adapter for hand or foot brake cylinder, for filling or bleeding the brake system
BRAKE BLEEDER COVER
Adapter for hand or foot brake cylinder, for filling or bleeding the brake system
UNIVERSAL MOUNTING RACK
Tool (including chassis, crank rotation mechanism, oil pan, and engine bracket) for mounting the rem...
SUPPORT CPL.
Tool for securing the removed engine on the engine work stand
RETAIN. ARM F. ENG.WORK STAND
Tool for securing the removed engine on the engine work stand
HOLDING SPANNER FOR FLYWHEEL
Tool for holding components (rotor)
LOCATING SCREW
Tool for securing components (crankshaft in TDC position)
BUSHING EXTRACTOR
Tool for removing bearings from a housing
INTERN.BEAR.PULLER 18-23 MM
Tool for removing bearings from a housing
MOUNTING TOOL F.BEARING NJ 207
Tool for pulling off components (inner bearing race of crankshaft)
EXTRACTOR PRIM. CPL.
Tool for pulling off components (primary gear wheel)
EXTRACTOR FOR TIMING GEAR
Tool for pulling off components (timing chain sprocket)
HOUSING SEPARATING TOOL
Tool for disengaging components (sections of the engine case)
MOUNT.SLEEVE F. SH.S.RING WAPU
Tool for protecting components (installation of crankshaft and balancer shaft)
MOUNT.SLEEVE F. SH.S.RING MS
Tool for protecting components (installation of crankshaft, balancer shaft and engine case)
MOUNT.SLEEVE F. SH.S.RING KS
Tool for protecting components (installation of crankshaft and balancer shaft)
PROTECTOR CAP F.CRANKSHAFT 07
Tool for protecting components (removal of primary gear wheel)
VEHICLE STAND
Tool for lifting the motorcycle at the center
BRACKET FOR ASSEMBLING RACK
Attachments for work stand, for lifting the motorcycle at the center
ATTACHMENT SHUNTING JACK CPL.
Attachment for floor jack, for lifting engine
